Kit Includes
- M18FPD Hammer Drill
- M18FID 1/4" Hex Impact Driver
- M18CAG125XPD 125mm Grinder
- M18FHZ-0 Fuel Hackzall
- M18CCS55-0 Circular Saw
- M18BBL-0 Blower
- 2 x 5.0Ah Li-ion Batteries
- M12-18FC Dual Fast Charger
- ONET-1
- Contractors Carry Bag
Milwaukee NEXT GEN 18V Fuel Hammer Drill M18FPD-0
Features:
- POWERSTATE Brushless Motor delivers 203 Nm of fastening torque for faster driving speeds
- REDLINK PLUS intelligence provides optimised performance and overload protection.
- REDLITHIUM battery technology provides more work per charge.
- 4-Mode DRIVE CONTROL provides greater control over output speed and power
- Self-Tapping Screw Mode
Specifications:
- Voltage 18V
- Length 197 mm
- No Load RPM 0-550 / 0-2,000
- Peak Torque 135 Nm
- BPM 32,000
- Chuck Type 1/2" Metal Single Sleeve - Ratcheting Lock
Milwaukee NEXT GEN 18V Fuel Impact Driver M18FID-0
Features:
- POWERSTATE Brushless Motor delivers 203 Nm of fastening torque for faster driving speeds
- REDLINK PLUS intelligence provides optimised performance and overload protection.
- REDLITHIUM battery technology provides more work per charge.
- 4-Mode DRIVE CONTROL provides greater control over output speed and power
- Self-Tapping Screw Mode
Specifications:
Voltage 18V
Length 133mm
No Load RPM 0-3,000
On Board FUEL Gauge Fuel Gauge on Battery
LED Light Yes
No Load IPM 0-3,700
Torque 203 Nm
Milwaukee Fuel 18v Brushless 125mm Angle Grinder M18CAG125XPD-0
The world's first cordless grinder delivers the power of a corded grinder with up to 2 x more run time and up to 10 x longer motor life.
The M18 FUEL 4-1/2" / 5" Grinder supplies maximum sustained power to complete the toughest grinding, surface preparation and cutting applications. The POWERSTATE Brushless Motor provides up to 10X longer motor life and lower cost of ownership. The M18 REDLITHIUM XC4.0 Battery Pack delivers up to 4 x more run time and 20% more power. The grinder features REDLINK PLUS Intelligence, the most advanced system of cordless power tool electronics, for maximum performance.
The 18-volt lithium-ion grinder's thin body design gives it optimized balance to rest easily in your hands. Tool-free accessory changes and guard adjustments mean less downtime during work. The grinder is built with the same tool body, gearing system and anti-vibration side handle as Milwaukee's legendary high-performance corded grinders for maximum durability on the job.
Features:
- POWERSTATE Brushless Motor: Delivers maximum power and up to 10X longer motor life
- REDLINK PLUS Intelligence provides optimized performance, electronic clutch, and overload protection using total system communication between tool, battery and charger
- REDLITHIUM XC 4.0 Battery Pack (not included) provides superior pack construction, electronics, and performance to deliver 2X more run-time and more work over pack life
- POWER TO GRIND: World's first cordless grinder with corded performance.
- DURABILITY: Same metal housing & gearing system as legendary high performance corded grinders
- 100% tool free: Make all accessory changes and guard adjustments without a wrench for increased productivity
- Slide switch: Reduces user fatigue
Specifications:
- Length 375mm
- Weight 5.8 lbs
- Tool Warranty 5 Years
- Battery Warranty 3 Year
- Switch Type Paddle
- Speed 8,500 RPM
- Trigger Lock Yes
- Vibration Reduction Yes
- Tool Free Guard Yes
- Arbor Size 5/8"-11
Milwaukee M18 Fuel Hackzall M18FHZ-0
The Milwaukee M18 fuel hackzall is the fastest cutting and most powerful one-handed reciprocating saw. Utilising a powerstate Brushless Motor and a best in class 22 mm stroke length, the M18 fuel hackzall cuts up faster. The compact, one-handed design provides superior control and the ability to make cuts in tight spaces. The dual gear counter balance mechanism provides lower vibration than traditional reciprocating saws, resulting in faster cut-starts in metal and reduced user fatigue. Redlink plus Intelligence ensures optimised performance and protects your investment from overload, overheating, and over-discharge. A rubber seal and weep holes provide superior protection against water and debris.
Features:
- Compact and Lightweight design allows for easier cutting in tight spaces or overhead applications
- One-handed design provides superior control and versatility over standard reciprocating saws
- 22 mm stroke length removes more material with each stroke resulting in faster cuts
- Pivoting shoe provides constant contact with the work-piece resulting in smoother cuts with less bucking and vibration
- Lower vibration for smooth cut starts & one-handed control.
Specifications:
- Length 355 mm
- Stroke Length 22 mm
- Shoe Pivoting Shoe
- Weight 1.85 kg
Milwaukee M18 Jobsite Radio/Charger - M18RC-0
Features:
- Shock absorbing metal handles
- Reinforced roll cage for extra protection
- Weather sealed auxiliary compartment for small belongings
- Flip-up stand for electronic devices
- 16 Aux input cort for corded connection
- Upgraded control panel with larger buttons for better control, even with gloves
- White on black LCD for increased visibility in direct sunlight
- Customizable equalizer and 10-station preset
- Digital processor with 40W applifier and premium speakers
- Built in bottle opener
- Quick convenient charging of all M18 batteries
Specifications:
- Voltage 18V
- Radio pre-set FM (10), AM (10)
- Frequency response 80Hz - 20Hz
- USB charger output 2.1 Amp
- Bluetooth Yes
- Dimensions (L x W x H) 304mm x 381mm x 304mm
- Weight 7.7kg
Milwaukee 18v Extended Capacity Red Lithium 5.0Ah Battery Pack M18B5
Features
- REDLINK Electronic Intelligence
- Overload protection to prevent battery abuse
- Temperature Management system to keep battery at ideal temperature
- Individual Cell Monitoring for optimal charge and discharge for maximum battery life
- Discharge Protection prevent cell damage from over-discharging
- For use with MILWAUKEE M18 cordless tools
- 2X MORE RUN-TIME
- 20% MORE POWER
- 2X MORE RECHARGES
Milwaukee Rapid Charge Station M12-18FC
Features:
- Charges all Milwaukee ® batteries up to 40% faster.
- Charges all M12 and M18 batteries.
- Sequential charging.
- REDLINK intelligence communicates directly with the battery.
- REDLINK monitors cell voltage and temperature.
- REDLINK charges to optimise the performance, protect and extend the life of the battery.
Milwaukee ONE-KEY Tick - 1 Pack - ONET-1
TICK TOOL AND EQUIPMENT TRACKER - Tracked by ONE-KEY, the TICK Tool and Equipment Tracker allows you to track the location of any item in your inventory, regardless of brand or type. The TICK was designed with the job-site in mind and it is the first tracking device built to survive the abuse your tools and equipment take every day.
RUGGED PROTECTION - Tools and equipment take abuse on the job. The TICK is designed specifically to survive in these conditions. The durable weatherproof design protects internal components from water and dust while UV rated plastics keep the TICK from getting brittle when exposed to sunlight for long periods of time.
Features
- TICK Tool and Equipment Tracker
- Attached with glue, screws, zip tie or rivets to anything
- Water, Dust and Impact resistant
- 1 year run-time with replaceable coin cell battery
- Over 30 m signal range
Part# | M18FPP5J-502B |
---|
Website Search...
- Located on the top of every page of website in between VEK TOOLS Logo & Website phone number
- For best results try to use key words for what you are looking for
- Sometimes too many words will reduce the chance of finding what your looking for
- Spelling errors will reduce the chance of finding what your looking for
- Once selection has been searched you can refine your search from left hand menu
Website Chat...
- Located on bottom right of website page
- This is run by real VEK TOOLS Staff so please be patient as they could be managing 2-10 chats at the same time
- This is service is not for tool diagrams or spare parts, contact via email prestons@vektools.com.au your request
- Remember if you don't give us details to contact you back on we can't get back to you
Stock Levels...
- Stock levels are not listed on website
- We also use supplier warehouses to dispatch orders to speed up delivery or save on costs when customer isn't in Sydney
- If out of stock we also search between supplier warehouses & also other distributor stores to fill orders
In Store Pick Up...
- If you don't want to pay for delivery or need your item/s ASAP, you can select pick up in store option in check out. Just bear in mind not all stores will have everything in stock & your order might need to be transferred from another store or supplier. Nominated store will contact you once order is in & ready for pick up.
- For urgent pick ups please call 02 9756 3464 to confirm store stocks & ensure order is processed as a priority order
Order Processing...
- Our online team will usually have your order processed within the next 2-4hours(During Business Hours)
- Once order is processed we will send an update through the online portal updating rough delivery times.Please ensure you check your spam or junk mail folders as with current filters sometimes order update emails are blocked or filed into those folders
- Orders placed before 1pm during working days will usually be dispatched by the 3pm pick up
- For urgent orders please don't hesitate to contact us on 02 9756 3464 so we can try make sure order is able to cover your expectations
Shipping...
- Unlike others we try run a flat rate service for our online orders, most times this is achievable & on occasions it can't be we will notify the best possible rate so you can choose whether you would like to proceed or if you would like to organise your own freight or if you would like to cancel your order. Refunds will be processed immediately.
- For items under 1kg & could fit in a shoe box size box you may select $10 local sydney metro freight rate even if your not in that location
LOCAL SYDNEY METRO
- For Sydney metro areas we offer flat rate of $10, some occasions to which this might not count is items longer that 1.2m or heavier than 20kgs. In these scenarios we will get in contact with you via phone or email before proceeding with order
- Includes the City of Sydney, Waverley, Randwick, Canada Bay, Inner West, Bayside and Woollahra local government areas. It is capped by Hornsby at the north, the Sutherland Shire at the bottom, but does not include areas like the Blue Mountains,Riverina,Illawarra,Shoalhaven, Riverina,Hunter,New England,North Coast, or the Central Coast.
OUT OF SYDNEY METRO
- For Areas outside the above region we offer a flat rate of $20, some occasions to which this might not count is items longer that 1.2m or heavier than 20kgs. In these scenarios we will get in contact with you via phone or email before proceeding with order
Estimated Delivery Times...
- Orders placed before 1pm on a business day will be processed within 1-3 hours. In the unusual event of a delay to the despatch of your order you will be contacted as soon as possible.
- Once the order has been despatched the estimated delivery time is as follows:
Sydney Metro 1-2 business days
QLD,VIC,SA Metro 2-4 business days
NT,WA,TAS Metro 3-6 business days
Regional Areas 3-8 business days
Remote Areas 6-10 business days
*Please note that these estimated delivery times are estimates and are not guaranteed
Order Tracking...
- Once order has left our warehouse tracking will usually come through to you mobile or email address
- Direct Warehouse shipments might be delayed as we are relying on supplier warehouse to notify us
Can power tools be purchased from other countries?
- Not recomended as the tool certification varies between different countries & in Australia tools require an Australian Compliance Approval number.
- In Australia tools must be 240v power compliance.
- Purchasing tools overseas will void your tool‘s warranty in Australia.
Can I plug my tool into a generator?
- Yes you can.
- Ensure that the generators constant out put is at least 30% more than the power tool you are running off it
- If running more than one tool make sure combined tool wattage is less than the constant out put of the generator by at least 30%
Can power tools be purchased from other countries?
- Not recomended as the tool certification varies between different countries & in Australia tools require an Australian Compliance Approval number.
- Purchasing tools overseas will void your tool‘s warranty in Australia.
- Tools from overseas can not be claimed on tax or depreciated over three years as they are not incurring GST
- In then event of injury caused by tool your public liabilty insurance policy will be void.
What can I do to maintain my power tool?
- Keep the tool relatively clean and free from debris.
- Try to use a blow gun to blast any dust and fragments from the unit occasionaly.
- Regularly check the carbon brushes if your tool has brushes, there are now tools that run on brushless technology Carbon brushes are a component in all power tools that wear with use, and should be replaced when they wear down to a marked point
- Both carbon brushes should be replaced at the same time, and should be identical. Once they are replaced, run the tool with no load for 1 minute to ‘break in’ the brushes. Use accessories that are sharp & of a high quality grade to avoid extra load on tool.
- Select the correct gear for the application to releave overloading tool.
- Let the tool do the work without extra force.
What’s that burning smell?
- If you encounter a burning smell when using a power tool of any sort, it means that the motor is being over loaded and is overheating. Specifically, the motor’s internal fan (air radiator) can’t cool the motor’s windings fast enough and their varnish coating begins to melt & burn. If you start to smell this ‘electrical burning smell’, withdraw the machine from the work but keep it running. This will enable the impeller fan to cool the motor’s windings.This smell is generally an indication that the tool isn’t being used correctly, or that it is attempting to perform a task that it isn’t capable of.
- If this does occur & performance of the tool has changed please ensure you get the tool to our inhouse service department to completely check before more damage is caused.
How can I ensure I don’t overload my power tool?
- Use the right tool for the job
- Using one or more pilot drills
- Taking smaller cuts and multiple passes over the material
- Using cutting and cooling lubricants
- Using quality, sharp accessories
- Slowing down the speed or changing to a lower gear
- Letting the power tool do the work and not forcing it
- Regularly clearing wood chips, debris & swarf
My power tool isn’t functioning properly, what do I do?
- If your tool is still under its warranty, then all you have to do is to take it back to our inhouse service department with your proof of purchase (Tax invoice), and we will assess it and give you a solution.
- If it is not under warranty, then you can take it to a local service agent or our inhouse service department and they will give you a quote to repair it.
I have lost my power tool’s instruction manual. Where can I get a replacement?
- Most suppliers will have a library of instruction manuals on their website available for you to download.
- If you find these are not available online, call the manufacturer as they will have them.
If for some reason your not sure please always check instruction manual of tool or contact your nearest store for advice & assistance.
How do I get the best run time & life out of my cordless tools?
- Always keep the battery’s contacts/terminals clean and from coming into contact with metal or moisture
- Store the batteries in a cool, dry place & dont leave in sun for long periods(eg, on metal roof or rear of ute/truck)
- Use accessories that are sharp & of a high quality grade to avoid extra load on cordless tool
- Select the correct gear for the application to releave over current draw on batteries
- Let the tool do the work without extra force
- On Cordless Drills when tightening the chuck always use hand not machine to close the jaws
Can I use a different battery in my cordless tool?
- Most cordless tool will only be able to operate off a single voltage, there are some tools that will run dual voltage please check your instruction manual before you attempt or call our customer service to check
- Some Cordless tools can run on batteries with different capacities (amp-hour values). Note: if your tools are made to run on 3ah they might not run on a 1.5ah battery or it might prematurely wear the 1.5ah battery
- Some manufacturers/brands do not change their style of battery fitment & are reverse compatible between battery chemistries (eg a Li-ion battery may be able to be fitted to a NiCd tool). If this is the case with your cordless tool, ensure your charger can charge the both battery types of chemistry.
How long will a battery’s charge last?
- This will vary on many factors such as:the condition of the battery, the battery’s voltage & Amp Hour, speed ratings of the tool, the tool’s gearing, the application, the tools accessory and the efficiency of the cordless tool.
- A good test is when you buy a new tool to fully charge the battery & time how long it takes to fully drain, so in the future you will be able to compare condition of battery to your test results
Can I leave my batteries on the charger when I’m not using them?
- This isn’t a good idea & could harm the battery or charger.
- On some charges it will overcharge the batteries after the nominal charging time has expired.
- Always charge the batteries in a safe enviroment away from the chances of being bumped or dropped whilst charging
Can cordless tools be purchased from other countries?
- Not recomended as the tool certification varies between different countries & in Australia tools require an Australian Compliance Approval number.
- Purchasing tools overseas will void your tool‘s warranty in Australia.
- Tools from overseas can not be claimed on tax or depreciated over three years as they are not incurring GST
- In then event of injury caused by tool your public liabilty insurance policy will be void
Can I plug my charger into a generator?
- Tool battery chargers should not be plugged into a generator.
- If you have to make sure the generator is an Invertor Generator or Single Sign Wave Generator
- There are some chargers available that can handle the surges in voltage and current that generators produce – If this is the case it will be specified by the charger’s manufacturer in the manual.
What can I do to maintain my cordless tool?
- Keep the tool relatively clean and free from debris.
- Try to use a blow gun to blast any dust and fragments from the unit occasionaly.
- Regularly check the carbon brushes if your tool has brushes, there are now tools that run on brushless technology Carbon brushes are a component in all power tools that wear with use, and should be replaced when they wear down to a marked point
- Both carbon brushes should be replaced at the same time, and should be identical. Once they are replaced, run the tool with no load for 1 minute to ‘break in’ the brushes.
- Use accessories that are sharp & of a high quality grade to avoid extra load on cordless tool
- Select the correct gear for the application to releave over current draw on batteries
- Let the tool do the work without extra force
What’s that burning smell?
- If you encounter a burning smell when using a power tool of any sort, it means that the motor is being over loaded and is overheating. Specifically, the motor’s internal fan (air radiator) can’t cool the motor’s windings fast enough and their varnish coating begins to melt & burn. If you start to smell this ‘electrical burning smell’, withdraw the machine from the work but keep it running. This will enable the impeller fan to cool the motor’s windings.
- This smell is generally an indication that the tool isn’t being used correctly, or that it is attempting to perform a task that it isn’t capable of.
- If this does occur & performance of the tool has changed please ensure you get the tool to our inhouse service department to completely check before more damage is caused
How can I ensure I don’t overload my cordless tool?
- Using one or more pilot drills
- Taking smaller cuts and multiple passes over the material
- Using cutting and cooling lubricants
- Using quality, sharp accessories
- Slowing down the speed or changing to a lower gear
- Letting the drill do the work and not forcing it
- Regularly clearing wood chips, debris & swarf
My cordless tool isn’t functioning properly, what do I do?
- If your tool is still under its warranty, then all you have to do is to take it back to our inhouse service department with your proof of purchase (Tax invoice), and we will assess it and give you a solution.
- If it is not under warranty, then you can take it to a local service agent or our inhouse service department and they will give you a quote to repair it.
I have lost my cordless tool’s instruction manual. Where can I get a replacement?
- Most suppliers will have a library of instruction manuals on their website available for you to download.
- If you find these are not available online, call the manufacturer as they will have them
If for some reason your not sure please always check instruction manual of tool or contact your nearest store for advice & assistance.
Which types of tools use compressed air?
The most common air tools are paint sprayers, air wrenches, air sanders, nail guns and air drills.
What are the advantages of using air tools?
- Air tools provide a lot more force than power tools driven by electric motors.
- Air tools have fewer moving parts and no electric motor to wear out making them more durable than power tools or cordless tools.
- Air tools can be used where tools creating spark can't such as service stations or other areas with highly flammable product enviroments
- Their durability and simplicity make them ideal for extended use in large-scale construction projects and in commercial factory work applications.
What extra equipment do I need to use air tools?
- To operate air tools, you will need a compressed air source, filtration and safety gear.
- Ensure that air compressor has a filter & air regulator
- Always wear goggles and any other safety gear specified by the air tool and air compressor safety instructions.
What can I do to maintain my air tool?
- Run the air tool at the right pressure
- Always have a clean air source by having the appropriate filtration to remove water from air lines
- Oil air tools regurlarly with quality air tool oil as per instruction manual of tool
- Use accessories that are sharp & of a high quality grade to avoid extra load on the air tool
How much air pressure is needed to operate an air tool?
- Most air tools will need at least 70psi (pounds per square inch) to operate.
- Most air tools will have markings or stickers on tool to stipulate max pressure
- Always check the instructions that come with your air tools and adjust the air compressor to fit the specifications.
I have lost my air tool’s instruction manual. Where can I get a replacement?
- Most suppliers will have a library of instruction manuals on their website available for you to download.
- If you find these are not available online, call the manufacturer as they will have them
If for some reason your not sure please always check instruction manual of tool or contact your nearest store for advice & assistance.